GNEE (Tianjin) Multinational Trade Co., Ltd
+8615824687445
Contact Us
  • Telephone: +86-372-5055135

  • WhatsApp / WeChat:+8615824687445

  • Mobile: +8615824687445

  • Mail:es@gescosteel.com

  • Address: No.4-1114, Beichen Building, Beicang City, Beichen District, Tianjin, China

Why is titanium alloy not easy to process?

Feb 08, 2023

The cutting force during titanium alloy processing is only slightly larger than that of steel of the same hardness, but the physical phenomenon of titanium alloy processing is much more complicated than that of steel processing, so processing titanium alloy faces great difficulties.
The thermal conductivity of most titanium alloys is very low, only 1/7 of steel and 1/16 of aluminum. Therefore, the heat generated in the titanium alloy cutting process will not be quickly transferred to the workpiece or removed by chips, but will be concentrated in the cutting area, the resulting temperature can be as high as 1 000 degree C or more, so that the cutting edge of the tool wears quickly, chipping and accumulated edge generation, rapid wear of the cutting edge and the cutting area generates more heat, shortening even longer tool life.
The high temperature generated during the cutting process also destroys the surface integrity of titanium alloy parts, resulting in a decrease in the geometric accuracy of the part and a work hardening phenomenon that seriously reduces its resistance to fatigue.
The elasticity of titanium alloys may be beneficial to workpiece performance, but during the cutting process, elastic deformation of the workpiece is an important cause of vibration. The cutting pressure causes the "elastic" workpiece to leave the tool and rebound, so that the friction between the tool and the workpiece is greater than the cutting effect. The friction process also generates heat, which compounds the problem of poor thermal conductivity of titanium alloys. This problem is exacerbated when machining deformable parts, such as thin-walled or annular parts, and machining thin-walled titanium parts with the expected dimensional accuracy is not an easy task. Because as the workpiece material is pushed by the tool, the local deformation of the thin wall has exceeded the elastic range and plastic deformation occurs, and the material strength and hardness of the cutting point increase significantly. At this point, machining at the previously determined cutting speed becomes too high, leading to acute tool wear.
"Hot" is the "culprit" for the difficult processing of titanium alloy!
2. Knowledge of the process for processing titanium alloys Based on the understanding of the processing mechanism of titanium alloys, coupled with previous experience, the main process tips for processing titanium alloys are as follows:
(1) Adopt a blade with a positive angle geometry
to reduce cutting force, cutting heat and workpiece deformation.
(2) Maintain constant feeding to avoid hardening of the workpiece, the tool should always be in the feeding state during the cutting process, and the radial feeding amount ae during milling should be 30% of the radius .
(3) High-pressure, high-flow cutting fluid is used to ensure the thermal stability of the machining process and prevent denaturation of the workpiece surface and tool damage caused by excessive temperature.
(4) Keep the edge of the blade, blunt tools are the cause of heat buildup and wear, which can easily lead to tool failure. (5) As far as possible, the softest state of the titanium alloy is processed, because the material becomes more difficult to process after hardening, and heat treatment improves the strength of the material and increases the wear of the blade.
(6) Use a large nose arc radius or chamfer to cut as many cutting edges as possible. This reduces cutting force and heat at each point and prevents localized breakage. When milling titanium alloys, the cutting speed has the greatest influence on the tool life vc among the cutting parameters, followed by the radial feed amount (milling depth) ae.

3. Start from the blade to solve the problem
of titanium processing The wear of the blade groove that occurs during the processing of titanium alloy is the local wear of the back and front along the cutting depth direction, which is often caused by the layer hardened surface left by pre-machining. The chemical reaction and diffusion between the tool and the workpiece material at a processing temperature of more than 800 degree is also one of the reasons for the formation of groove wear. Because during the processing process, the titanium molecules of the workpiece accumulate on the front area of ​​the blade and are "welded" to the cutting edge under high pressure and high temperature, forming a built-up edge. When the built-up edge is peeled off the cutting edge, the carbide coating is removed from the blade, therefore, titanium alloy processing requires special insert materials and geometries. 4. Structure
of the right tool for titanium processing The focus of titanium alloy processing is heat, and a large amount of high-pressure cutting fluid should be sprayed on the cutting edge in time and accurately to quickly remove heat . There are unique milling cutter structures on the market specifically for machining titanium.

¿Por qué la aleación de titanio no es fácil de procesar?


Related Products